Pulser8KApp module Release Notes

Version 1.0.22 (Jun-6-2024)
- Fixed: Do not restore VBias after a test is done. Restoring a VBias may change
	a device state in SOT devices.

Version 1.0.21 (Apr-24-2024)
- Added: SOT support is added. 
- Fixed: VSwitch does not generate correct set pulse if "Reset pulse before regular"
	is enabled.

Version 1.0.20 (Jan-17-2024)
- Added: In Prob-Error Sweep test, threshold results for high and low states 
	are added.
- Added: In Prob-Error Sweep test, "Read Out Delay" parameter is calculated 
	automatically and reported as a new result.
- Added: In Prob-Error Sweep test, lookup of comparator threshold for AC mode 
	is modified.

Version 1.0.19 (Dec-14-2023)
- Fixed: Prob-Error Sweep test does not generate correct reset pulses if test
	is sweeping on "Negative Side".

Version 1.0.18 (Sept-6-2023)
- Added: reset pulse option in HTransfer test.

Version 1.0.17 (Aug-23-2023)
- Fixed: Release for a new STTPulserLib3 v. 1.5.0

Version 1.0.16 (June-30-2023)
- Fixed: Remove "Keep" choice in "Auto-Detect By" parameter in 
	Prob Error test.

Version 1.0.15 (June-19-2023)
- Fixed: The min/max read VBias is changed to 3V in tests
- Added: reset field parameters are added in MTJ test

Version 1.0.14 (May-31-2023)
- Fixed: The max read VBias is changed to 3V in VSwitch test

Version 1.0.13 (May-1-2023)
- Fixed: In H-Transfer test, change auto QST gain adjustment criterion to
 fix problem in some DUT.
- Fixed: In V-Transfer test, add 20 ms delay after reset pulse so that it
has enough time to reset DUT.

Version 1.0.12 (Apr-13-2023)
- Fixed: If reset pulse width is larger than 655 us in Prob-Error Sweep test,
	runtime error will be displayed.

Version 1.0.11 (Apr-10-2023)
- Fixed: The reset pulse width limit in Prob-Error Sweep test is fixed
	to match hardware limit (5 ms max)
- Fixed: wrong statistical results if "Cycles" > 1 in H-Transfer test

Version 1.0.10 (Mar-23-2023)
- Fixed: Low Pos Rh and Rl results in V-Transfer are swapped
- Fixed: pos and neg low bias results are swapped in V-Transfer test
	if sweeping from pos bias to neg bias

Version 1.0.9 (Mar-21-2023)
- Fixed: "Auto QST Gain" gives wrong QST gain when negative VBias
	is used in H-Transfer test
- Added: new results in V-Transfer test

Version 1.0.8 (Mar-17-2003)
- Added: "Auto QST Gain" parameter is added in H-Transfer test.
- Added: "Auto Pulser Gain" parameter is added for tests using Pulser gain.
- Added: "Overflow" and "FinalPulserGain" results are added in tests: 
	H-Transfer, Read Disturb, RVHScan, Single Pulse, V Break Down, 
	V Switch, V Transfer, Write Prob

Version 1.0.6 (Mar-03-2023)
- Fixed: MTJ resistance test gives wrong "overflow" result if 
	negative bias is used.
- Fixed: H-Transfer test uses QST to measure reference resistance

Version 1.0.5 (Feb-28-2023)
- Fixed: wrong unit for Threshold result in Error Rate test
- Fixed: H-Transfer test does not work if "Amplitude Gain" is selected

Version 1.0.4 (Feb-24-2023)
- Fixed: "Pulse Width (us)" was used wrongly to reset when
	Asymmetric Pulse is enabled.

Version 1.0.3 (Feb-21-2023)
- Added: Pulser gain selection to tests
- Added: All tests, except HTransfer, use Pulser for measurement
- Fixed: "Asymmetric Pulses" in Prob-Error Sweep is never enabled
- Fixed: When "Enable Stop" is enabled, Endurance test stops 
		immediately even test results are good.

Version 1.0.2 (Jan-24-2023)
- Added: adjustment to measured resistances

Version 1.0.1 (Jan-20-2023)
- Added: make use of pulser-QST VBias

Version 1.0.0 (Jan-12-2023)
- Initial Release